- SMARTCRAFT SC1000 SYSTEM MONITOR MANUAL
- SMARTCRAFT SC1000 SYSTEM MONITOR FULL
- SMARTCRAFT SC1000 SYSTEM MONITOR SOFTWARE
Displays the engine temperature in degrees Fahrenheit (F) or Celsius (C).ĭisplays the engine temperature in degrees Fahrenheit (F) or Celsius (C).ĭisplays the engine oil temperature in degrees Fahrenheit (F) or Celsius (C). NOTE: This screen can be set to pop up whenever the trim switch is used.
SMARTCRAFT SC1000 SYSTEM MONITOR FULL
0 = down, 10 = full trim 25 = full trailer. Trim PositionDisplays trim position of the propulsion unit up to the maximum trim position, and then displays the trailer position. You can Reset anytime by pressing and buttons together momentarily.Įngine RPMTachometer Displays engine speed in Revolutions Per Minute (RPM).ĭisplays current estimated individual engine fuel consumption in Gallons per hour (Gal/hr) or Liters per hour (Ltr/hr).
SMARTCRAFT SC1000 SYSTEM MONITOR SOFTWARE
Depending on your type of engine, not all these screens will apply.Īt start up, a momentary (1 second) screen displays the current monitor software version, followed by a 4 second display showing hours of engine use.ĭisplays approximate fuel used since the last reset.
SMARTCRAFT SC1000 SYSTEM MONITOR MANUAL
STANDARD DISPLAY SCREENSNOTE:This manual shows all the Monitor display screens that are available. The SEt message flashing on the screen indicates that the unit has been reset to factory defaults. Immediately press and hold in unit counts down to zero 0. IMPORTANT: Performing a master reset will reset the unit back to all factory defaults, thus eliminating any installation calibrations performed during set up of product. MASTER RESETYou can return the gauge back to factory presets through the Master Reset command. Stnd = Stern Drive, Inbd = Inboard, JEtd = Jet Drive, Out2 = Outboard 2 Stroke, Out4 = Outboard 4 Stroke. Use the button to scroll through the choices. Flashing 2001 You will need to manually select your engine type. Engines may not be compatible or must be programmed for proper engine location by using a DDT or Quicksilver Diagnostic Tool. Flashing noSt None of the engine computers (ECMs) are configured as a starboard engine. Please check wiring for bad connections and for proper amount of terminator resistors. Flashing nonE The gauge does not see any engine computers (ECMs). The engines must be programmed for proper engine location using a DDT or Quicksilver Diagnostic Tool. Once all of the monitors display SEt then, perform autodetect on the monitors.4īASIC OPERATIONInitial Power Up (Or After Master Reset)INITIAL AUTO-DETECTION ERROR MESSAGES:Flashing Stbd More than one of the engine computers (ECMs) are configured as a starboard engine. When setting up monitors for multiengine or multistation installations, perform a power up or a master reset on all monitors before performing the autodetect function. It also checks for other Monitors to allow for appropriate engine location and station location setting. The intention is to make initial setup easier. In this procedure the Monitor checks with the engine control module (ECM) to see what type of engine you have and presets the data monitoring screens accordingly, (e.g., If Monitor detects an inboard engine connected to the data network it will turn off all engine/drive TRIM functions as these functions are not used in an inboard engine installation). Initial Power Up (Or After Master Reset)Unit will display software level then flash the word SEt in conjunction with engine icon, indicating it is ready to start the autodetect procedure.ĪUTO-DETECTION The unit will begin its Auto-detection of engine type procedure. In the event of a warning alarm, the warning icon(s) displayed. The backlight brightness is adjustable using button. The display includes a backlight which allows you to read it at night. The Monitor will power up when the ignition is turned on. displays can be activated using the button scrolls the following displays: fuel used, Pressing the tachometer (RPM), fuel flow, power trim position, engine temp, water pressure, battery voltage, range (if calibrated), and water depth (if equipped with transducer). = Engine = Fuel = Water Temperature = Water Pressure = Oil = AlarmīASIC OPERATIONThe Monitor is an LCD multi-function display gauge. LEGENDA= B= C= D= E= F= I= L= N= O= P= S= T= U= Depending on your type of engine, not all these screens will apply. 22 NOTE:This manual shows all the Monitor display screens that are available.
4 Initial Power Up (Or After Master Reset). Operation ManualTHIS MANUAL DESCRIBES THE SMARTCRAFT GAUGE SYSTEMS AVAILABLE FOR YOUR BOAT
0 kommentar(er)
